Aries-automotive P1050 User Manual download pdf

PARTS LIST:

Qty Description Qty Description

1 Grille Guard 20 12mm x 24mm OD x 2.5mm Flat Washers

1 Driver/Left Frame Mounting Bracket 10 12-1.75mm Nylon Lock Nuts

1 Passenger/Right Frame Mounting Bracket 2 10-1.5mm x 30mm Button Head Bolts

1 Driver/Left Top Mounting Bracket 4 10mm x 20mm OD x 2mm Flat Washers

1 Passenger/Right Top Mounting Bracket 2 10mm Nylon Lock Nuts

2 8mm Special Rod Bolts 2 8mm x 28mm OD x 3mm Large Flat Washers

10 12-1.75mm x 30mm Hex Bolts 2 8mm Nylon Lock Nuts

2 8mm Clip nuts 2 8mm Button head bolts

2 8mm Flat washers 2 8mm lock washers

1 Support flange

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS

CAREFULLY BEFORE STARTING INSTALLATION. CUTTING IS REQUIRED. ASSISTANCE IS

RECOMMENDED.

2. Starting under the front bumper of the vehicle, remove the plastic top fill plate between the bumper

and the radiator. Also remove the lower factory splash guard. Place both on a clean, stable work

surface.

3. Select the passenger side Frame Mounting Bracket. Bolt the Frame Mounting Bracket to the

bottom of the cross member with (1) 12mm x 30mm Hex Bolt, (2) 12mm Flat Washers and (1)

12mm Nylon Lock Nut. NOTE: 07-09 models will use the outer mounting location (Fig 1A), and

2010-13 models will use the inner mounting location, (Fig 1B). Insert (1) 12mm x 30mm Hex Bolt,

(2) 12mm Flat Washers and (1) 12mm Nylon Lock Nut through the upper tab on the side of the

Mounting Bracket upright and tighten hardware at this time, (Fig 2). Repeat this step to install the

driver side Frame Bracket, (Fig 1C).

4. Next, place the top fill plate back in position and mark a slot on the underside straight up from the

frame upright, (the top brackets slide into the frame upright-see Fig 5). Cut (2) slots to clear the

Top Brackets, (Fig 3). NOTE: Only cut a slot large enough to clear the Top Mounting Brackets.

Driver/Left Top

Mounting Bracket

Driver/Left Frame

Mounting Bracket

Passenger/Right Frame

Mounting Bracket

(2) 8mm Rod Bolts

Passenger/Right Top

Mounting Bracket

INSTALLATION INSTRUCTIONS

2007-13 JEEP WRANGLER

PART# P1050

Support Flange

(2) 8mm Nut Clips

1 2 3 4 5 6

INSTALLATION INSTRUCTIONS 1

Summary of Contents

Page 1 - INSTALLATION INSTRUCTIONS

PARTS LIST: Qty Description Qty Description 1 Grille Guard 20 12mm x 24mm OD x 2.5mm Flat Washers 1 Driver/Left Frame Mounting Bracket

Page 2

Page 1 of 5 IMPORTANT! Do not cut completely through front or rear edge of the fill panel. Reinstall the fil

Page 3

Page 2 of 5 14. Do periodic inspections of the installation to make sure that all hardware is secure and ti

Page 4

Page 3 of 5 Driver Side Installation Pictured Fig 3 Fig 5

Page 5

Page 4 of 5 Driver Side Installation Pictured Fig 7 Once

Page 6

Page 5 of 5 Installation complete (1) 10mm x 30mm Button Head All

Comments to this Manuals

No comments

Aries-automotive P1050 User Manual

Browse online or download User Manual for For the car Aries-automotive P1050. Aries Automotive P1050 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Aries-automotive P1050