Aries-automotive 206010-2 User Manual download pdf

PART# 206010/206010-2

2012 HONDA CRV

(Fig 1)

included (4) 10mm x 30mm Hex Head Bolts, (4) 10mm Lock Washers, and (4) 10mm Flat Washers

(Fig 3)

(Fig

each of the 8mm bolts. Transfer the openings

(Fig 1)

4 of

10mm x 22mm x 3mm Flat Washers

10mm Lock Washers

10mm x 30mm Hex Head Bolts

PARTS LIST:

1 Driver Side Bar 8-1.25mm x 30mm Hex Head Bolts

1 Passenger Side Bar 8mm Lock Washers

1 Rear Driver Side Mounting Bracket (A) 8mm x 22mm x 3mm Flat Washers

1 Front Driver Side Mounting Bracket (B)

1 Front Passenger Side Mounting Bracket (C)

1 Rear Passenger Side Mounting Bracket (D)

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ

INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.

2. Determine driver and passenger Mounting Brackets.

3. Hang the inner side of the driver front Mounting Bracket into position by partially threading (1)

8mm x 30mm Hex Head Bolt, (1) 8mm Lock Washer, and (1) 8mm Flat Washer into factory

threaded hole on the frame . NOTE: There are two threaded holes by the front mounting

location on the frame, use the one towards the rear of vehicle.

4. Attach the opposite side of the driver front Mounting Bracket to the threaded holes on the floor

panel of the vehicle by partially threading (2) 8mm x 30mm Hex Head Bolts, (2) 8mm Lock

Washers, and (2) 8mm Flat Washers .

5. Locate and cut out the openings in the driver and passenger side trimming templates with a pair of

scissors (Page 3 & 4)

6. Fit the driver’s side template onto its respective side plastic rock shields. Position them using two

in the templates onto the plastic cover using a magic marker.

7. Now remove the rock shield from the undercarriage of the car. The three front screws can be

removed with a 10MM socket. The plastic retainer plugs can be removed with a flat blade

screwdriver.

8. Using a sharp knife or pair of shares, cut out the shields as marked using the templates

2).

9. Insert the inner side of driver rear Mounting Bracket through previously cut out hole on the plastic

cover. Hang Mounting Bracket by partially threading (1) 8mm x 30mm Hex Head Bolt, (1) 8mm

Lock Washer, and (1) 8mm Flat Washer into factory threaded hole on the frame .

NOTE: There are two threaded holes on the frame, use the one towards the rear of vehicle.

10. Attach the opposite side on the driver rear Mounting Bracket by partially threading (2) 8mm x

30mm Hex Head Bolts, (2) 8mm Lock Washers, and (2) 8mm Flat Washers into factory threaded

holes on the floor panel.

11. Position Driver Side Bar onto Mounting Brackets. Attach Side Bar to Mounting Brackets using the

. Do not tighten at this time.

12. Level and adjust Side Bar; then tighten all hardware at this time.

13. Re-install the rest of fastener on the rock shield.

Page 1

INSTALLATION INSTRUCTIONS

(A)

(B)

(C)

(D)

14. Repeat steps 2-13 for passenger Side Bar.

15. Do periodic inspections to the installation to make sure that all hardware is secure and tight.

1 2 3 4

Summary of Contents

Page 1 - INSTALLATION INSTRUCTIONS

PART# 206010/206010-22012 HONDA CRV(Fig 1)included (4) 10mm x 30mm Hex Head Bolts, (4) 10mm Lock Washers, and (4) 10mm Flat Washers(Fig 3)(Figeach of

Page 2 - 10mm x 30mm Hex Bolts

4Fig 38mm Lock Washer, & 8mm x 30mm Hex Head Bolt,Fig 2Fig 1Front Driver Side Mounting Bracket ShownRear Driver Side Mounting Bracket Shown

Page 3

4 Page 3 of

Page 4

4 Page 4 of

Related models: 206010

Comments to this Manuals

No comments

Aries-automotive 206010-2 User Manual

Browse online or download User Manual for For the car Aries-automotive 206010-2. Aries Automotive 206010-2 User Manual

Summary of Contents

Related models: 206010

Comments to this Manuals

Related products and manuals for For the car Aries-automotive 206010-2