Aries-automotive 203032-2 User Manual download pdf

Page 1 of 3

2007-10 FORD EDGE

PARTS LIST:

1 Driver/Left Sidebar 2

10-1.50mm x 25mm Bolt Plate w/ Bent (small) (G)

1 Passenger/Right Sidebar 4

10-1.50mm x 30mm Bolt Plate (H)

Driver/Left Front Mounting Bracket (A)

10-1.50mm x 35mm Bolt Plate w/ Bent (Large) (I)

Passenger/Right Front Mounting Bracket (B)

4 10-1.50mm x 25mm Hex Head Bolts

Driver/Left Rear Mounting Bracket (C)

12 10mm Nylock Nuts

Passenger/Right Rear Mounting Bracket (D)

16 10mm ID x 26mm OD x 1.5mm Flat Washers

Driver/Left Front Support Bracket (E)

8 8-1.25mm x 25mm Hex Head Bolts

Passenger/Right Front Support Bracket (F)

8 8mm Lock Washers

8 8mm ID x 22mm OD x 1.5mm Flat washers

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS

CAREFULLY BEFORE STARTING INSTALLATION. DO NOT ATTEMPT INSTALLATION ALONE;

PERSONAL INJURY OR DAMAGE TO THE TRUCK MAY RESULT.

2. From underside of vehicle, insert (1) 10mm x 30mm Bolt Plate into factory front hole on the passenger side panel

(Figure 1).

3. Determine passenger and driver side front Mounting Brackets. Hang passenger side front Mounting Bracket

through Bolt Plate and into position by partially threading (1) 10mm Nylock Nut and (1) 10mm Flat Washer into

previously inserted Bolt Plate (Figure 2).

4. Insert (1) 10mm x 35mm Bolt Plate w/ Bent into factory hole on the frame (Figure 3).

5. Locate passenger side front Support Bracket. Partially hang passenger Support Bracket through previously

inserted Bolt Plate and into position by threading (1) 10mm Nylock Nut and (1) 10mm Flat Washer (Figure 4).

6. Attach opposite side of passenger Support Bracket to Mounting Bracket by using the included (2) 10mm x 25mm

Hex Head Bolts, (2) 10mm Nylock Nuts, and (4) 10mm Flat Washers (Figure 4). Do not tighten at this time.

7. The passenger rear Mounting Bracket mounts with two Bolt Plates. Insert (1) 10mm x 25mm Bolt Plate w/ Bent

into the two factory holes on the cross member (Figure 5). Insert (1) 10mm x 30mm Bolt Plate into lower factory

hole on the side panel (Figure 6).

8. Determine passenger and driver side rear Mounting Bracket. Position Mounting Bracket through both previously

inserted Bolt Plates and partially thread (1 ea ) 10mm Nylock Nut and (1 ea ) 10mm Flat Washer to secure

Mounting Bracket (Figure 7).

9. Locate the passenger/right Side Bar and carefully place it onto previously installed Mounting Brackets.

WARNING! Do not slide Side Bar back and forth on the Mounting Brackets; this may damage the finish on the

Side Bar.

INSTALLATION INSTRUCTIONS

SIDEBAR PART #203032-2/203032

(A) (B) (C) (D)

(E) (F)

(G) (G)

(H) (H)

(I) (I)

1 2 3

Summary of Contents

Page 1 - INSTALLATION INSTRUCTIONS

Page 1 of 3 2007-10 FORD EDGE PARTS LIST: 1 Driver/Left Sidebar 2 10-1.5

Page 2

Page 2 of 3 10. Align holes on the Side Bar with holes on the Mounting Brack

Page 3 - Figure 8 Figure 9

Page 3 of 3 10mm x 30mm Bolt Plate

Related models: 203032

Comments to this Manuals

No comments

Aries-automotive 203032-2 User Manual

Browse online or download User Manual for For the car Aries-automotive 203032-2. Aries Automotive 203032-2 User Manual

Summary of Contents

Related models: 203032

Comments to this Manuals

Related products and manuals for For the car Aries-automotive 203032-2