Aries-automotive 25630 User Manual
Browse online or download User Manual for For the car Aries-automotive 25630. Aries Automotive 25630 User Manual
- Page / 5
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
PARTS LIST:
Qty Description Qty Description
1 3
rd
Light bracket 8 8mm Lock Washer
8 8mm x 25mm Hex Bolt 8 8mm Hex Nuts
16 8mm ID x 30mm OD Flat Washer
PROCEDURE:
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ
INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
2. Start by removing the tire and then the factory tire carrier by open the back door, locate the plastic
louvered cover (Fig1) pry the cover’s corners to remove this cover, once removed locate the plug
for the factory 3
rd
brake light and unplug it (Fig 2), push the wire and the rubber grommet out so
that the wire is completely removed from the door, (Fig 3) place the new rubber plug into hole
sealing it.
3. Once wire is removed from door, remove the bolts holding the factory carrier to the rear door (Fig
4) place the carrier on a flat work space as you will need to measure from the bottom line as seen
in (Fig 5) 3 1/2" up mark with a line (mark on both sides right side left side, so your line is level)
once marked you will need to cut with either a cut off wheel on a grinder or a hack saw. Slowly
making your cut to keep the cutline true.
4. Once carrier is separated select the new 3
rd
brake light bracket and place it into place coupling the
rear of carrier, the edge of the bracket should sit flush with the edge of the carrier as seen in (Fig
6,7&8) taking note of the alignment, mark holes through the bracket to the carrier for drilling the
(4) holes on the bottom (use a 3/8” size drill bit) with these holes drilled it is easier to attach (2) of
the 8mm hex bolts (4) 8mm washers & (2) 8mm hex nuts snug but do not tighten for the
measuring of the top holes to be drilled.
Page 1 of 5 6/1/2012
INSTALLATION INSTRUCTIONS
2007-12 JEEP JK 3
RD
BRAKE LIGHT BRACKET
Part 25630TBL
(
works with 25630
)
3
r
d
brake light
bracket
Summary of Contents
Page 1 - INSTALLATION INSTRUCTIONS
PARTS LIST: Qty Description Qty Description 1 3rd Light bracket 8 8mm Lock Washer 8 8mm x 25mm Hex Bolt 8 8mm Hex Nuts 16 8mm
Page 2 - Fig 3 Fig 4
5. Once lower part of bracket is attached measure from the lower cut edge up to the top cut edge (distance apart) 3” as seen in (Fig 9) make sure t
Page 3 - Measurements
Page 1 of 5 6/1/2012 Cut line Measure 3 1/2" From bottom to cut line Measure 3 1/2&quo
Page 4
Page 1 of 5 6/1/2012 Fig 6 Fig 7 Fig 8 Fig 9 Align with bottom of bracket Measure 2” Fro
Page 5
Page 1 of 5 6/1/2012 Installation completeFig 10 Attach with (2) 8mm Hex bolts (4) 8mm Flat w
More documents for For the car Aries-automotive 25630
Aries-automotive 25630 User Manual
(1 pages)
Related products and manuals for For the car Aries-automotive 25630
(3 pages)© 2020, manymanuals.com. All rights reserved. | 0.620 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals